Slopoe-Top 1200 a

Heavy Commercial for Hot Water of Steam

Specially designed for commercial use in heavy traffic areas. Unique one-piece heavy duty enclosure with polyurethane powder coated finish applied after fabrication. Easy installation - simply secure brackets to wall, run element and snap on enclosure

*Stocked in 2-3-4-5-6-7-8 foot lengths, both complete (with elements) and enclosure only (less element).

Table 1 - Heating Capacities, BTU per hr per lin. ft. 65 degrees entering air temperature I-B-R approved

model

Nom. Tube Size

Fin
Dimensions
H X W

Thick-
ness

Fin
Spacing
Fins/Ft.

Dimension
'A'

Water
Rate
GPM

Hot Water Ratings
Average Water Temperature degrees F

Slope-Top
ST 1200 -1A

3/4"
CPR.

2 1/2" X 3 1/4"
Alum. Natural Finish

.015

3 7/16"

150	160	170	180	190	200	210	220	230	240
580	680	770	870	960	1060	1160	1260	1350	1450
550	640	730	820	910	1000	1100	1190	1280	1370

Slope-Top
ST 1200 -S125

1 1/4"
IPS
Steel

3 1/4" X 3 1/4"
Painted

Steam BTU.
1010 sq ft/hr 4.2

.029

3 13/16"

500	580	670	760	850	940	1030	1110	1200	1290
470	550	630	720	800	890	970	1150	1140	1220

Slope-Top
ST 1200 -3A

1 1/4"
CPR.

3 X 3 1/4"
Alum. Natural Finish

Steam BTU.
1290 sq ft/hr 5.4

.020

3 11/16"

560	670	770	880	980	1090	1190	1300	1410	1510
530	630	730	830	930	1030	1130	1230	1330	1430

All the above I-B-R Ratings are based on active length, which is 3" less than total length, and includes a 15% addition for heating effect.
Ratings: Heating capacities are listed in Table 1 for two flow rates: 1 GPM and 4 GPM. The use of I-B-R Ratings at 4 GPM is limited to installations where the water flow rate through the baseboard unit is equal to or greater than 4 GPM. Where the water flow rate through the baseboard is not known, the I-B-R Ratings at the standard flow of 1 GPM must be used.

Note: If the calculated water flow rate through a baseboard unit in a completely designed hot water heating system is greater than the standard flow rate (1 GPM), the rating of that unit may be increased by multiplying the standard I-B-R Rating at 1 GPM by the factor shown for the calculated flow rate.

Table 2 - Factors for ratings at flow other than standard and pressure drop values
Rate of Flow GPM	1.0	1.5	2.0	2.5	3.0	3.5	4.0	4.5	5.0	6.0
Factor	1.000	1.016	1.028	1.038	1.045	1.051	1.057	1.062	1.067	1.074
Pressure Drop 3/4" Tube Mill inches per ft.	47	96	157	230	320	420	525	650	775	1060
Pressure Drop 1 1/4" IPS Steel Pipe Mill in. per ft.	3	7	12	17	24	32	41	51	62	88
Pressure Drop 1 1/4" Tube Mill inches per ft.	6	12	20	28	39	50	63	77	93	124